Cerca
Italian
All Categories
    Menu Close

    Geekcreit CNC Shield + UNO R3 Board + 4 X DRV8825 Driver Kit For Arduino 3D Printer

    Produttore: Serier Electronics
    Geekcreit CNC Shield + UNO R3 Board + 4 X DRV8825 Driver Kit For Arduino 3D Printer



    €23,90




    i h
    - CNC Shield Board

    Version: 3.0
    Color: Red
    Size(L*W*H): 68 x 53 x 18 mm
    Voltage: DC 12~36 V

    Features:
    1. Uses removable A4988 or DRV8825 compatible stepper drivers.
    2. The extension board can be used for carving machine, 3 d printer driver expansion board
    3. GRBL 0.8 compatible. (Open source firmware that runs on an Arduino UNO that turns G-code commands into stepper signals)
    4. PWM Spindle and direction pins,4-Axis support (X, Y, Z , A-Can duplicate X,Y,Z or do a full 4th axis with custom firmware using pins D12 and D13)
    5. Compact design. Stepper Motors can be connected with 4 pin molex connectors or soldered in place.
    6. Please note that this is an unassembled kit and Basic soldering skills are needed.


    - DRV8825 Stepper Motor Driver

    The module has an interface pinout is almost the same with A4988 stepper motor drive carrier, so that it can be used as a higher performance in a pull-down menu the plates replaced in many applications.
    DRV8825 features an adjustable current limit, overcurrent and overtemperature protection, six micro-resolution (down 1/32-step).
    It uses 8.2 - 45V, can provide up to about 1.5 per phase no heat sink or forced air flow (rated up to 2.2 per volume sufficient additional cooling).


    Features:
    Simple step and direction control interface
    The interface can connect directly with 3.3V and 5V systems
    Support over-temperature thermal shutdown, over-current shutdown and under-voltage lockout
    Support short-to-ground and shorted-load protection
    Six different step resolutions: full-step, half-step, 1/4-step, 1/8-step, 1/16-step, and 1/32-step
    4-layer, 2 oz copper PCB for improved heat dissipation
    Adjustable current control support you to set the maximum current output with a potentiometer, which lets you use voltages above your stepper motor’s rated voltage to achieve higher step rates
    Intelligent chopping control that automatically selects the correct current decay mode (fast decay or slow decay)
    45V maximum supply voltage
    Built-in regulator (needed external logic voltage supply)


    - Uno
    -R3 Board

    MCU: ATmega328
    Clock speed: 16 MHz
    USB interface: ATmega16U2
    Operating voltage: 5 V
    I-I / O pin output current: 40 mA max
    3.3 V output current: 150 mA max
    Digital I/O pins: 14 (including 6 with PWM capability)
    Analog input pins: 6
    EEPROM: 1 kB
    Static RAM (SRAM): 2 kB
    Flash memory: 32 kB
    Size(L*W*H): 68 x 53 x 10 mm


    Click to download universal course

    Package included:

    1 x Uno-R3 Board
    1 x CNC Shield Board
    4 x DRV8825 Stepper Motor Driver
    4 x Heat Sink
    1 x USB Cable
    1 x 40-Pin Row Needles

    ,,,,,
    0.0 0
    Scrivi una recensione Close
    • Il prodotto può essere recensito solo dopo l'acquisto
    • Solo gli utenti registrati possono scrivere recensioni
    *
    *
    • Pessimo
    • Eccellente
    *
    *
    *
    Etichetta del prodotto